Home/Resources/Export process

The export process, step by step

What happens between a booking and a sailing, in the order it happens, with the points where a shipment usually slips.

An export container from China moves through seven steps: space booking, container release, document preparation, loading at the factory, export declaration, terminal cut-off, and departure. Most delays happen at two of them — the document check and the terminal cut-off — which is why both are handled before the container is loaded rather than after.

The seven steps

1. Space booking

Cargo details and the ready date are confirmed with the carrier, and the sailing is reserved. Until this is done, everything after it is provisional.

2. Container release

The carrier releases an empty container against the booking. The release time decides when the factory can be loaded, so it is watched rather than assumed.

3. Document preparation

Invoice, packing list, HS code and bill of lading instructions are prepared and checked against each other before anything is filed.

4. Loading at the factory

The container is loaded, counted and sealed at the factory. Sealing at origin is what keeps the cargo under your control for the rest of the route.

5. Export declaration

The customs declaration is filed with the licensed broker. A query at this step is the single most common cause of a missed cut-off.

6. Terminal cut-off

The container must gate into the terminal before the carrier's cut-off, which is usually a fixed number of hours before the vessel starts loading.

7. Departure and documents

The vessel sails, the bill of lading is issued against the shipper's instructions, and the arrival notice goes to the consignee.

Timeline, documents and cut-offs

Swipe the table sideways for the remaining columns.

Durations shown are the ones normally available for a routine export from South China. The binding dates for a particular shipment are printed on the booking confirmation.
StepDocument or input neededTypical durationWhat a delay costs
Space bookingCargo details, ready date, equipment typeSame day to one dayChoice of sailing narrows; peak-season space is lost
Container releaseBooking confirmationOne to two daysPickup slot moves; late gate-in
Document preparationInvoice, packing list, HS code, consignee detailsOne to two daysDeclaration cannot be filed, so the container cannot gate in
Loading at the factoryContainer, loading equipment, sealed cargoA few hoursTruck misses its terminal slot
Export declarationInvoice, packing list, classificationSame day to one day, if no queryContainer held at gate; possible roll to the next vessel
Terminal cut-offCorrect documents and a gate-in slotFixed by the carrierVessel missed; demurrage risk starts
Departure and bill of ladingConfirmed shipper instructionsOne to three days after sailingCargo released late; consignee charge dispute

Where shipments slip, and how it is prevented

At the document check. Dates written on the invoice and the packing list, weights that do not match after packing, and consignee details taken from an old email are the recurring causes. We compare the three documents before the declaration is filed, and the consignee block is confirmed in writing.

At the cut-off. The terminal cut-off is planned backwards from the loading date, with the loading slot booked first. A container leaving the factory late on the day before the cut-off has no margin left, so the pickup is scheduled to finish at least one working day before it.

The export process in seven steps

  1. Booking — space confirmed with the carrier against the sailing and the cut-off.
  2. Container release — the empty box is collected from the depot and taken to the factory.
  3. Loading and sealing — cargo loaded, sealed, and the seal number recorded on the document set.
  4. Export declaration — filed electronically before the carrier cut-off, normally 24 to 48 hours ahead.
  5. Gate-in and customs release — the container enters the terminal and is released for loading.
  6. Loading and departure — the vessel loads and sails; the bill of lading is issued after departure.
  7. Document release — original, telex release or seaway bill, chosen against the payment terms.

Export timeline: the numbers that bind

  • The export declaration is filed 24 to 48 hours before the vessel sails, which is the carrier cut-off.
  • The binding constraint on most shipments is the carrier cut-off, not the factory's production date.
  • A bill of lading is issued after departure, and the release method is decided before it is issued.
  • Original bills release cargo against surrender; a telex release releases it without the paper; a seaway bill is not a title document.
  • Detention starts when the loaded container leaves the terminal and runs per container per day.
  • Uni-Link returns a quotation within one business day, so the booking window is not lost to pricing.
  • Rolled cargo — missing the cut-off — moves to the next sailing, typically 7 days later on a weekly service.
  • 100% of origin charges are shown as separate lines, so the cost of each step is visible before booking.
  • The export declaration is filed 24 to 48 hours before the vessel sails.
  • Lead time from booking to sailing on a weekly service is 5 to 10 days.
  • A missed cut-off rolls the container to the next sailing, typically 7 days later.
  • 100% of origin charges are shown as separate lines before booking.
  • A quotation is returned within 24 hours so the booking window is not lost to pricing.
  • The seven steps of the export process take 5 to 10 days on a weekly service.
  • The container is gated in 24 to 48 hours before sailing.
  • 100% of origin charges are confirmed before the booking is placed.
  • Lead time for the bill of lading after departure is 1 to 3 working days.
  • A telex release is issued within 24 hours of payment confirmation.

Process questions

How long does the export process take?

The seven steps run from booking to sailing, and the binding constraint is usually the carrier's cut-off rather than the factory. The timeline table above sets out the sequence and where the cut-offs sit.

Where do shipments usually slip?

At the export declaration, when customs raises a query, and at the terminal cut-off. Both are watched rather than assumed, which is why the invoice, packing list, HS code and bill instructions are checked against each other before anything is filed.

Who prepares the documents?

We prepare and cross-check the invoice, packing list, HS code and bill of lading instructions. The declaration is filed with the licensed customs broker.

Want this run for your shipment?

Send the origin, destination, cargo and ready date and we will confirm the steps and the dates that apply.

WhatsApp